A garbage disposal that's been making grinding sounds for months before stopping entirely often has a seized bearing or cracked impeller โ signs the motor isn't worth repairing. Our techs in Lyons tell you honestly whether a repair or a same-day unit swap makes more financial sense.
๐ Call +1-855-718-1500 โ Same-Day Service
Garbage disposal failures have specific, diagnosable causes. Our techs don't just swap units โ they identify what failed and whether repair or replacement is the right call for your situation.
A disposal that hums but won't spin almost always just needs the jam cleared with an Allen wrench at the center socket and the reset button pressed โ a 5-minute fix that doesn't require a new unit.
InSinkErator (Badger, Badger 5, Compact, Evolution series), Moen GXS/GX series, Waste King, KitchenAid, and Whirlpool disposals all mount differently and have specific jam-clearing procedures. We know the mounting assembly for each brand and carry the correct jam-clearing wrench sizes.
We give you the actual cost comparison. If clearing the jam and pressing the reset button fixes it, that's what we do. If the motor has failed, we show you the replacement options and install same-day.
A disposal installed without properly removing the dishwasher drain knockout plug is a common installation error that floods the dishwasher interior. We check this and correct it if present.
From a simple jam clear to a full replacement with drain reconnection, here's how we handle each garbage disposal scenario in Lyons, WI.
If the jam-clearing wrench won't budge the impeller, the motor shaft may be seized rather than just stuck from debris โ we distinguish between the two before recommending replacement.
A disposal that makes no sound when switched on has either tripped its thermal overload protector (the red button on the bottom โ press it and try again) or has a wiring issue at the switch or disposal unit. We check the reset button, test for power at the disposal's wire connection, and test the wall switch for continuity.
Disposal leaks come from three locations: the sink flange (top of the unit where it mounts to the sink drain opening โ repaired by re-sealing the flange with plumber's putty and re-tightening the mounting ring), the side port (dishwasher drain hose connection โ usually a loose hose clamp or cracked fitting), or the bottom of the unit (internal body crack or failed internal seal โ indicates replacement needed).
If the turntable bearing has failed โ indicated by a loud rumbling throughout operation rather than specific impact sounds โ that's an internal motor wear failure that warrants replacement.
If the slow drain persists after cleaning the drain arm and p-trap, a camera scope of the kitchen drain line is the next step to check for blockage further downstream.
Replacement includes: safely disconnecting electrical at the junction box under the sink, removing the old unit and mounting assembly, installing the new unit with correct wiring and plumbing connections, testing for full jam-free operation, and verifying zero leaks at all connections before leaving.
No guesswork โ we diagnose before we quote, and quote before we start.
Hums but won't spin, completely silent, grinding noise, leaking, or slow to drain โ each symptom tells our dispatcher which tools and possible replacement units to have on the truck. Knowing the disposal brand is a plus but not required.
The tech identifies the failure type in minutes: jam test at the motor socket, reset button check, power confirmation at the wire connections, leak source tracing. We know what each symptom means and we go straight to confirming it.
You decide. We don't upsell replacement when repair is the right answer, and we don't push a cheap repair that won't hold on a unit that's genuinely at end of life.
We leave the cabinet dry and the disposal running quietly. If a dishwasher drain hose was involved, we run a dishwasher cycle to verify no backup occurs.

The disposal under our kitchen sink was 12 years old and started leaking from the bottom โ which the tech explained is always an internal seal failure, not a repairable condition. He had a replacement 3/4 HP InSinkErator on his truck, installed it in about 45 minutes, and the kitchen is back to normal. Old unit got pulled, new unit tested clean, no leaks at any connection.
Disposal making a loud rattling noise but still grinding. Tech took out a bottle cap that had gotten past the splash guard and was spinning around the grinding chamber. Cleaned out the chamber, confirmed the impeller wasn't damaged, tested for smooth operation. Twenty-minute visit, everything working perfectly.
Old disposal stopped working completely โ no hum, nothing. I assumed the motor failed. The tech checked the wiring first โ found a loose wire nut at the junction box under the sink that had vibrated loose over the years. Reconnected the wire, reset the overload button, disposal came right on. Would have been embarrassing if I'd bought a replacement unit. Masters Plumbing Service's thoroughness saved me a few hundred dollars.

Masters Plumbing Service dispatches garbage disposal repair and replacement technicians throughout Lyons and the broader Lyons, WI service area. Most calls are same-day โ call to check today's availability.

Call now โ same-day service available in Lyons and across Lyons, WI.
๐ Call +1-855-718-1500 Now